The latest C1000 Pure Clear Coolant launched by Thermaltake is utilized either as a transparent coolant or to mix with TT Premium Concentrate Series to customize the coolant color users desire. This high performance new member is made in Germany, virtually odorless and non-flammable, plus it features anti-corrosion protection and heat-transfer medium for PC water-cooling and superb protection for copper, nickel, brass, and aluminum. Create your own coolant color and experience the excitement of color mix & match.

German-Made Anti-Corrosive Solution

Being non-flammable, Thermaltake C1000 Coolant Series is a ready-to-use cooling solution with at least 3 years shelf life in airtight containers, providing great performance while preventing the entire cooling system – copper, brass, nickel, and aluminum – from corrosion.

Biodegradable Material

Thermaltake C1000 Coolant Series is classified in water hazard class 1 (low-rate endangering) according to German water hazard regulations. The product is readily biodegradable.

Vivid Application

Thermaltake C1000 Opaque Coolant is designed specifically for PC liquid cooling systems. Featuring anti-freezing, anti-rusting, water scale prevention and easy application, the C1000 non-transparent coolant brings vivid colors into your build and delivers great thermal efficiency and further reduce the temperature of the system.

Specifications

• Capacity: 1000 ml
• Color: Pure Clear

Hazardous components list

• Ethanediol Value < 20%
• CAS 170-21-1
• EG 203-473-3
• Index 603-027-00-1
• Certificate Xn
• R-Phrase 22
• S-Phrase 2, 24/25,46

Caution!

May be harmful if swallowed, may cause birth defects. May cause respiratory tract, eye and skin irritations. Keep out of reach of children. Avoid breathing any vapors or spray mists. Use with adequate ventilation. Avoid contact with skin and eyes. Keep container tightly closed when not in use. Wash thoroughly after handing. Store in a cool place.

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.

Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.

It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.

Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.

Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.

DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately

Fill the reservoir to the top as it will prevent air from going into the pump

If necessary tilt the system slightly from side to side to bleed the air out of the loop.

Place some paper towels under fittings and joining points to test for leaks.

Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop

Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.

Coolant might fade over time

Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.

DO NOT let the pump run dry, when there is no liquid entering the pump turn off your

Fill the reservoir to the top as it will prevent air from going into the pump

If necessary tilt the system slightly from side to side to bleed the air out of the loop.

Place some paper towels under fittings and joining points to test for leaks.

Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop

Please note:

• This item is not eligible for courier delivery due to the contents thereof.

Manufacturer's link